Hits: 957 img
In a silicone store or a supplier's catalog, you've surely seen two products with strikingly similar names: one called "condensation-cure silicone," the other "addition-cure silicone." The names differ by only a couple of characters, yet the prices can differ severalfold, and the applications are worlds apart—the former is mostly used for molds, sealing, and ordinary bonding, while the latter monopolizes the high-end arenas of medical, food, electronics, and precision injection molding.
Many newcomers' first reaction: isn't this just a matter of quality—better versus worse? The expensive one is obviously better.
That understanding is wrong. The two are not "good and bad grades of the same thing," but two entirely different technological routes—different in chemical reaction, curing method, what they can and cannot do, all governed by two separate logics. And the fork between these two routes is decided by precisely the protagonist of this series: the catalyst. That's why "the catalyst decides" is both literally true and the essence of the industry.
I. A Recap: Hardening Is "Weaving a Net," but the Weaving Methods Differ
As the principles article explained, the essence of silicone curing is "laterally connecting" independent molecular chains into a three-dimensional network. The process is like weaving a net—but there's more than one way to weave.
Condensation-cure uses a "spit out a thread" weaving method. Its molecular chains carry special reactive end groups, which, with the help of a catalyst (usually a tin-based or titanium-based compound), react with moisture in the air, or with a small-molecule crosslinker in the system. The hallmark of this reaction: every knot tied "spits out" a small molecule—possibly an alcohol, an acid, a ketoxime. It's like weaving a net while scraps of thread keep falling away.
Addition-cure uses a "one-step click" weaving method. The vinyl groups on the molecular chains and the silicon-hydrogen bonds on the crosslinker click together directly under the platinum catalyst's matchmaking—every knot tied releases nothing, with not one atom more or less. Remember the "wedding" analogy: the matchmaker makes the introduction, the couple joins hands, zero emissions throughout.
Note the key point here: the two routes hire different "foremen." Condensation-cure hires relatively cheap metal catalysts like tin or titanium; addition-cure hires platinum. Who you hire as foreman determines the entire site's construction method and the quality of the finished building. That is the first meaning of "the catalyst decides."
II. Five Report Cards Revealing the Divide Between the Two Routes
The differences between the two routes ultimately show up in the few things users care about most. Let's go through them one by one.
First card: cleanliness. Condensation-cure constantly spits out small molecules while curing, and those "loose threads" that can't escape remain in the product or volatilize out—this is why condensation-cure silicone often has an odor and sometimes corrodes objects (the acid-releasing type produces acid; you can smell the distinct vinegar odor, and it corrodes metal and glass). Addition-cure has zero emissions and is clean, odorless, and non-corrosive after curing. The gap on this card directly draws the market boundary: anywhere that goes into the mouth, into the body, or against precision components, condensation-cure is out.
Second card: shrinkage and deformation. Spitting out small molecules means the system "loses weight"—condensation-cure shows relatively noticeable shrinkage when curing, and thick sections may deform or crack because the insides can't finish expelling their byproducts. Addition-cure has minimal shrinkage and dimensional stability—that's the confidence behind its precision injection-molded parts and optical components.
Third card: deep curing. Many condensation-cure systems need moisture from the air to participate, and moisture takes time to penetrate from the surface inward—thick parts end up "dry outside, wet inside." Addition-cure doesn't depend on outside participation; as long as there's heat, the deep sections click together too—large, thick parts are its home turf.
Fourth card: the reverse-aging problem. Condensation-cure has an interesting ailment called "reversion": in certain systems, if the environment changes after curing (for example, being sealed in a dry, moisture-free space), the reaction may quietly run backwards, and the product gradually softens and turns tacky. Addition-cure's click-together is "nailed shut"—once clicked, it's extremely hard to undo, and performance stays stable long-term. Medical catheters rely on precisely this to guarantee their service life.
Fifth card: mutual adhesion. Here's an easy trap to step in: silicones from the two routes basically don't bond to each other. Pouring addition-cure silicone over cured condensation-cure (or vice versa), the two layers are very hard to bond firmly. The reason: the two routes leave different surface chemistries behind, and they simply "have no chemistry" with each other. For encapsulation or secondary molding processes, figure out the layering relationship before choosing a route—this is a very practical engineering consideration.
III. So Why Does Condensation-Cure Still Exist?
At this point, some readers may ask: if addition-cure wins across the board, why not just phase out condensation-cure?
Because it holds one overwhelming advantage: convenience and cheapness.
Condensation-cure products are single-component or simply proportioned: open the cap and use, just spread it on, cures at room temperature—no oven, no metering equipment, no platinum-priced catalyst needed. Patching a window frame gap, casting an undemanding mold, doing a routine bond—using addition-cure would be cracking a nut with a sledgehammer, expensive and troublesome. Condensation-cure is like "instant noodles" at the market: nutrition isn't great, but it's cheap, convenient, and good enough—the demand will always be there.
Addition-cure, meanwhile, is like a "carefully proportioned meal": it requires weighing, ratio control, and heat curing—but the output is clean, the nutrition controllable, and it can grace a fine dining table. The trade-off between convenience and quality is the entire logic of the two routes.
Incidentally, let's correct a common naming habit: the industry often calls addition-cure silicone "platinum silicone" and condensation-cure simply "silicone." They sound like category names, but in essence they're both shorthand for catalyst routes—next time you hear these terms, you'll know what's being talked about.
IV. How to Choose: Three Practical Criteria
For those hesitating between the two routes, here are three decision criteria.
Look at the product's "degree of bodily contact." Anything touching food, the human body, pharmaceuticals, or precision electronics leaves no room for hesitation—go directly to addition-cure. For ordinary industrial bonding, sealing, and standard molds, condensation-cure offers better value.
Look at thickness and structure. Thick walls, large volumes, deep potting—choose addition-cure to avoid "dry outside, wet inside." Thin coatings and surface bonding—either route can handle them.
Look at the layering relationships. For multi-layer molding or bonding to existing silicone layers, first determine which route the existing layer is—within the same route (addition-on-addition), bonding can be achieved with primers and similar means; across routes, a dedicated solution is required. Never take it for granted.
V. Summary
Addition-cure versus condensation-cure is not a difference of good
versus bad, but of two technological routes: the one hiring platinum as foreman
achieves one-step clicking, zero emissions, minimal shrinkage, thorough deep
curing, and lasting performance—at the price of expense and exacting standards.
The one hiring tin or titanium ties knots by spitting out small
molecules—convenient, cheap, ready to use—at the price of insufficient cleanliness,
shallow curing limits, and mediocre long-term stability. And the source of this
entire divide is the choice of catalyst—the catalyst decides.
Diethylenetetramethyldisiloxane platinum complex (platinum catalyst) MY 8112